MS36-76
Pump House and Fuel Tank Kit
£19.99
/
Tax included.
Shipping calculated at checkout.
A small fuel depot, based on the 3 tanks which existed near Buxton Station, Derbyshire at Buxton TMD.
The tanks are supplied with two different stands, the taller versions are for if you don't wish to model the concrete slabs (not included) inside of the containment walls which they stand on. The shorter versions are for if you wish to model the concrete slab, which goes approximately a third of the way up the containment walls.
The concrete slabs could be represented by a 6mm (OO) 10mm (O) thick piece of card, plywood or any other suitable material. The tank slab should measure 87mm (OO) 152mm (O) x 42mm (OO) 74mm (O).
No instructions are included as assembly is relatively simple, and part locations are shown in the item images.
Dimensions (assembled) L x W x H (mm):
OO - 151 x 62 x 65
OO - 151 x 62 x 65
O - 264 x 95 x 115
PLEASE SELECT AN OPTION BELOW
Product Information
Assembly
All of our products ship as fully assembled models unless stated otherwise. If the model is in kit form, instructions are provided and we are more than happy to help if you're stuck, simply contact us on the form below. The colours of the models you receive may vary from the images shown, however they will usually be dark grey, and this makes no difference to the quality or finish of the product. Superglue is recommended if your product requires assembly, as our prints are resin poly cement does not work.
Post Processing
Although effort has been taken to remove all support material, some stubs may remain. These can easily be eradicated with light sanding or filing. Please ALWAYS use a respirator when sanding resin. Take care around delicate areas however, as resin is very brittle, especially around parts such as window frames/thin parts.
Finishing
It is advised to prime your model before painting, however models will accept paint without priming first. Tamiya Fine Surface Primer is recommended. After priming, the models work well with any types of paint usually used for modelling, alongside washes, weathering powders etc. Models do NOT need washing prior to being painted. Both heat and water damage 3D printed resin. Any damage caused by this is non-refundable. Models are NOT suitable for garden railways/outdoor use. It's best to seal your model with matte varnish after painting, to protect against water absorption from high humidity environments.
Refund policy here - Refund policy – MS Models
Refund policy here - Refund policy – MS Models
Quality
Should you find yourself in the unlikely scenario where you are dissatisfied with the product which you receive, or you receive a product which does not meet the quality level you expected, please contact us and we will do our best to rectify the situation as soon as possible.
Scales
Should you have a wish to obtain a product which is not readily available in your chosen scale, please contact us and we'll be happy to assist you and do our best and compromise to work things out, however sometimes some items are not feasible to produce in all scales.
Please make you understand what scale you are modelling prior to ordering - OO9 and N gauge are NOT the same scale although they run on the same width track!
OO9 requires buildings listed as OO9 and OO
O16.5/NG7 requires buildings listed as O16.5 and O
Scales listed in numerical format e.g. 1:76.2 are listed next to items - these need to match to make sure your items are the same scale.
Please make you understand what scale you are modelling prior to ordering - OO9 and N gauge are NOT the same scale although they run on the same width track!
OO9 requires buildings listed as OO9 and OO
O16.5/NG7 requires buildings listed as O16.5 and O
Scales listed in numerical format e.g. 1:76.2 are listed next to items - these need to match to make sure your items are the same scale.
Bespoke Models/Product Requests
We are currently not accepting bespoke model requests.
Should you want to suggest a product, please contact us using the form below, however please be aware that some things are not feasible to produce due to a varying reasons.
General Tips
It's best to leave your items out of direct sunlight and heat, as they are prone to warping in excessive temperatures. We can't be held liable for any incidents which occur due to this.
Last revision 04/01/2024
Payment
